產品描述
Aqua-Poly/Mount is a water-soluble, non-fluorescing, non-permanent, aqueous mounting medium formulated for mounting sections directly from aqueous solutions. It is useful for immunofluorescent techniques as it enhances and retains fluorescent stains.
Aqua-Poly/Mount can also be used for frozen sections, fat stains and immuno-stains where aqueous mounting media is required. Aqua-Poly/Mount can be used with most fluorescent dyes and stains including DAB, Alkaline Phosphatase-Fast Red, AEC (aminoethylcarbazole) and other chromogens that are alcohol soluble or incompatible with organic solvents.
Aqua-Poly/Mount solidifies under the coverslip after 24-48 hours at a relative humidity of 20-50%. After it dries completely it forms a solid, clear seal that facilitates handling and storage, making painting of the coverslip edges unnecessary. Aqua-Poly/Mount can be used on automated coverslippers in place of traditional solvent based coverslipping medium.
使用方法
使用方法
Prepare slides as required. Prior to coverslipping rinse the slides in distilled or deionized water. The excess fluid can be drained, but blotting is not recommended. Aqua-Poly/Mount is supplied in convenient 20ml dropper bottles for manual staining and in larger volumes for automated coverslippers.
Apply two drops of Aqua-Poly/Mount to the slide at the end or over the tissue. Carefully lower the coverslip at an angle while gently applying pressure to force any excess medium and air bubbles away from the tissue and out from under the coverslip. It is helpful to draw the coverslip to the edge of the coverslipping medium and then lower it slowly while applying pressure. Gently tilt the slide to remove any medium at the edges of the slide and coverslip. The slide can be viewed immediately or after drying. Slides can be dried at room temperature or at 4°C. Drying at 4°C will increase drying times. Do not heat the slides as this can damage or fade some stains or reactions. Slides containing fluorescent chromogens should be stored in the dark.
Aqua-Poly/Mount can be used on automated coverslippers in place of traditional solvent based coverslipping medium. The viscosity of the medium may require adjusting for proper flow rates. Allow the liquid to come to room temperature before making any adjustments for flow rate as the viscosity will change. The amount of medium dispensed will effect the drying time. Thicker sections will require more coverage with medium to assure the coverslip remains in place against the slide surface.
貨號 | 品名 | 規格 | 品牌 |
78OC10006-20mL | Aqua-Poly/Mount | 20mL | BIOHUB |
相關產品
免責聲明
- 凡本網注明“來源:化工儀器網”的所有作品,均為浙江興旺寶明通網絡有限公司-化工儀器網合法擁有版權或有權使用的作品,未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的,應在授權范圍內使用,并注明“來源:化工儀器網”。違反上述聲明者,本網將追究其相關法律責任。
- 本網轉載并注明自其他來源(非化工儀器網)的作品,目的在于傳遞更多信息,并不代表本網贊同其觀點和對其真實性負責,不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時,必須保留本網注明的作品第一來源,并自負版權等法律責任。
- 如涉及作品內容、版權等問題,請在作品發表之日起一周內與本網聯系,否則視為放棄相關權利。