您好, 歡迎來到化工儀器網
YTK-01·02·03系列壓力控制器主要技術參數
設定點誤差：±2.5%（校準后1%以內）
指示誤差：±4%
重復性誤差：1.5%
控制誤差：±2.5%控制方式：一位式控制—常閉或常開
兩位式控制—常閉及常開
產品簡介
詳細介紹
YTK-01·02·03系列壓力控制器
Series pressure controller
Series pressure controller
YTK-01·02·03系列壓力控制器簡 介
YTK系列壓力控制器適用于對無爆炸危險的非結晶和非凝固介質的壓力進行位式控制，同時發出燈光信號，并按被測對象的各異，分別制成有壓力指示和無壓力指示等多種類型。
Brief introduction：
YTK series pressure controller is suitable for controlling pressure of liquid medium by position controlling , and the medium is non-crystalloid and non-concretionary, and has no danger of explosion. Lighting signal is sent out simultaneously. Due to difference of measured objects, pressure controller can be manufactured into manifold types, such as having pressure indication and not having pressure indication.
構成示意圖
YTK-01·02·03系列壓力控制器主要技術參數
- 設定點誤差：±2.5%（校準后1%以內）
- 指示誤差：±4%
- 重復性誤差：1.5%
- 控制誤差：±2.5%控制方式：一位式控制—常閉或常開
兩位式控制—常閉及常開 - 設定點調整范圍（為壓力范圍上限值）：
無指示值：15～*
有指示值：20～75% - 切換差（為壓力范圍上限值）：
一位式（固定）：不大于10%
兩位式（可調）：10～30% - 觸點容量：AC380V×2A或
AC220V×3A - 信號指示燈工作電源：AC380V或
AC220V - 絕緣強度：50Hz正弦交流電2000V，絕緣電阻＞20ΜΩ，歷時一分鐘不出現飛弧擊穿現象。
- 使用環境：-25℃～70℃，相對濕度不大于85%
- 溫度影響：不大于0.4%/10℃
Principal technical parameters
- Set point error: ±2.5%（after being adjusted, less than 1%）
- Indicating error: ±4%
- Repeatability error: 1.5%
- Control error:±2.5%
- Control mode: one position controlnormal close or normal open wo position control-- normal close and normal open
- Adjusting range of the set point （upper limit of pressure range）：not having indicating value: 15～*
- Having indicating value: 20～75%
- Differential gap （upper limit of pressure range）
- one position （immovable）: no more than 10% two position （adjustable）: 10～30%
- Contacting capacity: AC380V×2A or AC220V×3A
- Power supply of signal indicating lamp: AC380V or AC220V
- Insulation intensity: 50Hz sine AC 2000V,Insulation resistance is bigger than 20MΩ,lasting a period of one minute no arc breakdown phenomena appears.
- Applicable circumstance: -25℃～70℃, relative humidity is no more than 85%
- Temperature influence: no more than 0.4%/10℃
結構原理
控制器由測量系統，控制裝置，調整機構、氖燈顯示，指示裝置以及外殼和插頭座等組成。
控制器的工作原理是基于檢測元件（測量系統中的彈簧管）的彈性變形來驅使機能元件（控制裝置中的微動開關）產生快速的開關跳躍動作。即在被測（控）介質的壓力作用下，迫使彈簧管之末端產生相應的彈性位移，而與管端相連的微動開關中的按鈕（推桿）也隨之產生相應動作，待壓力達到所設定的控制值之瞬時，開關觸點即切換，致使控制系統中的電路予以斷開或接通，并同時發出燈光信號，以實現自動控制和發信號的目的。
Configuration principle
Pressure controller is composed of measuring system, controlling device, adjusting machine, neon light displaying, indicating device, crust and jack plug.
Operating principle of the controller is based on elastic deformation of testing component （spring tube used in measure system）, which can drive functionality component （micro switch used in controlling device） to produce jump action quickly. Under the action of measured （or controlled） medium, spring displacement will occur accordingly at the end of spring tube. As a result, the button （handspike） of micro switch connecting to the end will act also. Once pressure reaches defined control value, switch contactors will switch immediay and circuit of control system will be cut off or switch on. Lighting signal is sent out simultaneously, and aim of autocontrol and signal sending is gained.
型號表示
標記示例：YTK-03F 產品電腦編碼0260020401
壓力控制器YTK-03耐腐型，可調帶指示。產品電腦編碼詳見《壓力控制器系列儀表選型指南》。
Mark example: YTK-03F Electronic code 0260020401
Pressure Controller YTK-03 corrosion model control & show for further information on computer code, please see the
“Guide for type selection of pressure series Pressure Controller"
型號規格
| 型號 | 標度范圍（MPa） |
| YTK-01 | 0～0.25，0～0.4，0～0.6，0～1，0～1.6，0～2.5，0～4，0～6，0～10，0～16，0～25，0～40，0～60 |
| YTK-01F | |
| YTK-02 | |
| YTK-02F | |
| YTK-03 | |
| YTK-03F |
控制器電路及接線方法
外形尺寸
壓力控制器系列儀表選型指南
| 產品電腦編碼 Electronic code | 型號 Model | 產品名稱 Product name |
| 0210020401 | YTK-01 | 壓力控制器Pressure Controller |
| 0240020401 | YTK-01F | 壓力控制器Pressure Controller |
| 0220020401 | YTK-02 | 壓力控制器Pressure Controller |
| 0250020401 | YTK-02F | 壓力控制器Pressure Controller |
| 0200020401 | YTK-03 | 壓力控制器Pressure Controller |
| 0260020401 | YTK-03F | 壓力控制器Pressure Controller |
訂貨須知:
訂貨時須注明：產品電腦編碼、型號、名稱、精確度等級、測量范圍。如特殊要求，訂貨時請注明。
Ordering instructions: The product computer code ,types, names, accuracy grades, and measuring ranges .must be clearly noted. In case of special requirements, technical requirements shall be clearly noted specifications on the back of the order on ordering goods.