成人做爰免费视频免费看_成人a级高清视频在线观看,成人a大片在线观看,成人a大片高清在线观看,成人av在线播放,一a一级片,一级黄 中国色 片,一级黄 色蝶 片,一级黄色 片生活片

上海鼎振儀器設備有限公司
中級會員 | 第10年

13472521719

當前位置:首頁   >>   資料下載   >>   PV3987高光耐磨測試方法

PV3987高光耐磨測試方法

時間:2021-3-9閱讀:1693
分享:
  • 提供商

    上海鼎振儀器設備有限公司
  • 資料大小

    486.9KB
  • 資料圖片

  • 下載次數

    136次
  • 資料類型

    PDF 文件
  • 瀏覽次數

    1693次
點擊免費下載該資料

上海鼎徵儀器儀表設備有限公司
滿足大眾PV3987高光耐磨試驗標準會用到我公司代理的 BYK4563光澤度儀,德國Erichsen249耐磨儀、美國taber5900往復式耐磨試驗機 Rubbing adapter C  刮擦頭
Scrub Resisitance(Micro-Scrach Resistance)of High-Gloss Surfaces in the Vehicle interrior

 

Preface
This satandard supersedes the “Audi AG Provisional Test Specification”and Test Specification PV3975(“Matindale Scrub Resistance”)
Previous issues
PV3987:2016-08
Changes
The folloowing changes have been made to PV3987:2016-08
- section 3.1“Test equipment”:exanple changed
1 Scope
This PV describes a method for testing the micro-Scratch resistance and scrub resistance on high-gloss surfaces
A surface is referres to as high-glossy if the gloss level measurement at an angle of 60° is >70GU。Further gloss level measurements are performed with a measuring angle of 20°
 
This test method is suitable for determining the properties of uncoated (Eg PA PMMA)and coat-ed high-gloss surfaces (eg paint ,in-mold decoration(IMD),in-mold labeling(IML))when they are exposed to low-force friction loads。The load is roughly equivalent to that of the cleaning process the test must be performed on plane surfaces
 
The test determines the relative chang in gloss that is generated by rubbing/Scrubbing with polishing paper on the high-gloss surface
 
2 Designation
Scrub resistance (Micro-scratch resistabce)as per PV3987
 
3 Testing
3.1 Test equipment

Test  equipment Crochmeter as per DIN EN ISO105-X12 or a different testing device with which the required test conditions can be set(testing force 9N,Testing path:104±3mm)
Test  headRubbing adapter C as per DIN55654 (see figure1)
Test equipment/rubbing mediumRolishing paper as per DIN55654:Abrasive grain made of aluminum oxide,semi-open coat density of grain,grain 5um,bonding of grain with full synthetic resin on flexible ,extruded PES film (eg 3M261X)
Cut the polishing paper to an exact width of 25mm and a minimum length of 75mm
Gloss measuring deviceMeasure the gloss level using a reflectometer (as per DIN EN ISO 2813) at angle of 20°

 

3.2 Specimen preparation
A minimum Specimen size of 150mmx100mm is required to perfprm the test
Conditioning
There must be at least 7 days between specimen preparation and testing
For conditioning ,plan for 45h in a standard atmosphere as per VW50554-23/50-2 condition hydrophilic materials(eg polyamides)for 7 days in a standard atmosphere
Specimen preparation
Clean the specimen gently under luder lukewarm running water using only your wet hand
 
A mild laboratory flushing agent that does not leave a greasy residue can be used as a cleaning agent
The surfaces to be tested must not be damaged as a result of cleaning
Then rinse the specimen thoroughly with clear water
Dry the specimen by blowing it off with oil-free compressed air
After cleaning,condition hydrophilic materrials once again for 24h in a standard atmosphere

 

 

3.3 Test procedure
1 condition (see section3.2)
2 clean (see section3.2,for hydrophilic materials ,repeat conditioning if necessary)
3 Meassure the gloss level befor scratching,Measure the gloss level at a measuring angle of 20°
4 Rub/Scratch:Befeor each rubbing process,Clamp in a new rubbing medium。One rubbing
 Process comprise 5 double strokes。Rub with a load of 9N。If the rubbed track is not uniform
(streaky spotted),perform a repeat test
5 After rubbing,store the specimens at room temperature for 24h
6 Measure the gloss level on the track 。Align the gloss measuring device in such a way
 That  themeasuring direction is 90° relative to the rubbing direction。Make sure that the measuring hole of the gloss measuring device rests on the rubbed surface。Do not measure the first and last 10mm of the rubbed track。
 
3.4 Evaluation/assessment
Determine the scrub resistance as a relative change in gloss level(%)with respect to the initial
Gloss level。The measuring angle is 20°
Calculate the relative change in gloss level as follow:
(initial gloss level - gloss level after rubbing)x 100 / initial gloss level

 

4 Applicable documents
The following documents cited in this standard are necessary to its application
Some of the cited documents are translations from the German original。The translations of German terms in such documents may differ from those used in this stand,resulting in terminologocal inconsistency

 

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~
撥打電話
在線留言
主站蜘蛛池模板: 久久国产精品亚洲77777| 国产人妻精品一区二区三区不卡| 麻豆国产精品一二三区| 久久日韩精品无码一区| 国产特黄级AAAAA片免| 日韩精选亚洲一区| 亚洲欧美中文日韩在线| 天堂男人天堂网| 日韩欧美高清一区| 亚洲熟妇无码乱子AV电影| 久久精品中文騷妇女内射| 久久久久久久久九九九| 久久午夜免费视频| 麻豆传煤网站app入口直接进入在线下载| 韩日三级电影在线| 亚洲精品综合在线影院| 99无码熟妇丰满人妻啪啪| 国产亚洲第一伦理第一区| 欧美乱妇无码毛片斯巴达三百勇士| 日韩欧美中文字幕在线四区| 国产12孩岁A片被A午夜| 亚洲欧美精品日韩| 久热香蕉在线爽青青| 贪图隔壁的人妻中字| 成人午夜精品久久久久久久| 日韩欧美亚洲中文字幕第二页| 韩国免费漫画全集在线观看| 久久久国产精品无码一区二区| 午夜伦理yy44008影院| 亚洲欧美日韩精品| 女邻居拉开裙子让我挺进| 国产福利秒拍weipai.ee| 91免费在线播放| 久久精品中文字幕一区二区| 啊灬啊灬啊灬快灬深高潮啦| 欧美激情四射在线视频| 中文字幕欧美一区| 无码人妻国产一区二区三区| 少妇又大又粗又硬啪啪| 国产又黄又猛又粗又爽的A片| 色-情-伦-理一区二区三区电影|